View PE8350306_1295023.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Product Specification
PE83503
Product Description
The PE83503 is a high-performance monolithic UltraCMOSTM prescaler with a fixed divide ratio of 8. Its operating frequency range is 1.5 GHz to 3.5 GHz. The PE83503 operates on a nominal 3 V supply and draws only 12 mA. It is packaged in a small 8-lead MSOP and is ideal for microwave PLL synthesis solutions. The PE83503 is manufactured on Peregrine's UltraCMOSTM process, a patented variation of silicon-on-insulator (SOI) technology on a sapphire substrate, offering the performance of GaAs with the economy and integration of conventional CMOS. Figure 1. Functional Schematic Diagram 3.5 GHz Low Power UltraCMOSTM
Divide-by-8 Prescaler
Military Operating Temperature Range Features
* High-frequency operation:
1.5 GHz to 3.5 GHz
* Fixed divide ratio of 8 * Low-power operation: 12 mA typical
@ 3 V across frequency
* Small package: 8-lead MSOP * Low Cost
Figure 2. Package Type
8-lead MSOP
D IN Pre-Amp
Q
D
Q
D
Q OUT Output Buffer
CLK QB
CLK QB
CLK QB
Table 1. Electrical Specifications (ZS = ZL = 50 )
2.85 V VDD 3.15 V; -55 C TA 125 C, unless otherwise specified
Parameter
Supply Voltage Supply Current Input Frequency (FIN) Input Power (PIN)
Conditions
Minimum
2.85
Typical
3.0 13
Maximum
3.15 19 3.5 +10 +10
Units
V mA GHz dBm dBm dBm
1.5 1500 MHz Fin 2800 MHz 2800 MHz < Fin 3500 MHz -5 0 0
Output Power
Document No. 70-0126-02 www.psemi.com
(c)2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 1 of 8
PE83503
Product Specification
Figure 3. Pin Configuration (Top View)
1 8
Electrostatic Discharge (ESD) Precautions When handling this UltraCMOSTM device, observe the same precautions that you would use with other ESD-sensitive devices. Although this device contains circuitry to protect it from damage due to ESD, precautions should be taken to avoid exceeding the rating specified in Table 3. Latch-Up Avoidance Unlike conventional CMOS devices, UltraCMOSTM devices are immune to latch-up.
VDD
GND
IN
2
7
OUT
PE350 PE83503
DEC 3
3
6
GND
GND
4
5
GND
Table 2. Pin Descriptions
Pin No.
1 2
Pin Name
VDD IN
Description
Power supply pin. Bypassing is required. Input signal pin. Should be coupled with a capacitor (eg 15pF) Power supply decoupling pin. Place a capacitor as close as possible and connect directly to the ground plane (eg 10 nF and 10 pF). Ground pin. Ground pattern on the board should be as wide as possible to reduce ground impedance. Ground pin. Ground pin. Divided frequency output pin. This pin should be coupled with a capacitor (eg 100 pF). Ground pin.
Device Functional Considerations The PE83503 takes an input signal frequency from 1.5 GHz to 3.5 GHz and produces an output signal frequency one-eighth that of the supplied input. In order for the prescaler to work properly, several conditions need to be adhered to. It is crucial that pin 3 be supplied with a bypass capacitor to ground. In addition, the input and output signals (pins 2 & 7, respectively) need to be AC coupled via an external capacitor as shown in the test circuit in Figure 7. The ground pattern on the board should be made as wide as possible to minimize ground impedance.
3
DEC
4 5 6 7 8
GND GND GND OUT GND
Table 3. Absolute Maximum Ratings
Symbol
VDD TST TOP VESD PINMAX
Parameter/Conditions
Supply voltage Storage temperature range Operating temperature range ESD voltage (Human Body Model) Maximum input power
Min
Max
4.0
Units
V C C V dBm
-65 -55
150 125 250 15
Absolute Maximum Ratings are those values listed in the above table. Exceeding these values may cause permanent device damage. Exposure to absolute maximum ratings for extended periods may affect device reliability.
(c)2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 2 of 8
Document No. 70-0126-02 UltraCMOSTM RFIC Solutions
PE83503
Product Specification
Figure 4. Test Circuit Block Diagram
VDD 3 V +/- 0.15 V
+ -
10 pF
1000 pF 1 8 7 100 pF 50
50
15 pF 2
PE83503
3 Signal Generator 4 5 6
Spectrum Analyzer
10 nF
10 pF
Figure 5. High Frequency System Application The wideband frequency of operation of the PE83503 makes it an ideal part for use in a DBS downconverter system.
INPUT FROM DBS 1ST IF
BPF
SAW
AGC
FM DEMOD
BASEBAND OUTPUT
DIVIDE-BY-8
PE3291 PE83503
LOWNoise Low NOISE PLL PLL SYNTH SYNTH
LPF
Document No. 70-0126-02 www.psemi.com
(c)2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 3 of 8
PE83503
Product Specification
Typical Performance Data: VDD = 3.0 V Figure 6. Input Sensitivity Figure 7. Device Current
Figure 8. Output Power
(c)2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 4 of 8
Document No. 70-0126-02 UltraCMOSTM RFIC Solutions
PE83503
Product Specification
Evaluation Kit
Evaluation Kit Operation
The MSOP Prescaler Evaluation Board was designed to help customers evaluate the PE83503 Divide-by-8 Prescaler. On this board, the device input (pin 2) is connected to connector J1 through a 50 transmission line. A series capacitor (C3) provides the necessary DC block for the device input. It is important to note that the value of this capacitance will impact the performance of the device. A value of 15pF was found to be optimal for this board layout; other applications may require a different value. The device output (pin 7) is connected to connector J3 through a 50 transmission line. A series capacitor (C1) provides the necessary DC block for the device output. Note that this capacitor must be chosen to have a low impedance at the desired output frequency the device. The value of 100pF was chosen to provide a wide operating range for the evaluation board. The board is constructed of a two-layer FR4 material with a total thickness of 0.031". The bottom layer provides ground for the RF transmission lines. The transmission lines were designed using a coplanar waveguide above ground plane model with trace width of 0.030", trace gaps of 0.007", dielectric thickness of 0.028", metal thickness of 0.0014" and r of 4.4. Note that the predominate mode for these transmission lines is coplanar waveguide. J2 provides DC power to the device. Starting from the lower left pin, the second pin to the right (J2-3) is connected to the device VDD pin (1). Two decoupling capacitors (10 pF, 1000 pF) are included on this trace.
It is the responsibility of the customer to determine proper supply decoupling for their design application. The DEC pin (3) must be connected to a low impedance AC ground for proper device operation. On the board, two decoupling capacitors (C6 = 10 nF, C4 = 10 pF), located on the back of the board, perform this function.
Applications Support
If you have a problem with your evaluation kit or if you have applications questions call (858) 731-9400 and ask for applications support. You may also contact us by fax or e-mail: Fax: (858) 731-9499 E-Mail: help@psemi.com
Figure 9. Evaluation Board Layouts
Peregrine Specification 101/0035
Figure 10. Evaluation Board Schematic
Peregrine Specification 102/0200
Document No. 70-0126-02 www.psemi.com
(c)2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 5 of 8
PE83503
Product Specification
Figure 11. Package Drawing
8-lead MSOP
TOP VIEW 0.65BSC 8 7 6 5 .525BSC
2.450.10 2X 3.000.10
0.510.13 -B1 2 3 4 .25 A B C
0.510.13
2.950.10
-C0.860.08 2.950.10
1.10 MAX -A0.10 A 0.33+0.07 -0.08 0.08 ABC 3.000.10 FRONT VIEW SIDE VIEW 0.100.05 3.000.10 4.900.15
(c)2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 6 of 8
Document No. 70-0126-02 UltraCMOSTM RFIC Solutions
PE83503
Product Specification
Figure 12. Tape and Reel Specifications
8-lead MSOP
Pin1
Table 4. Ordering Information
Order Code
83503-21 83503-22 83503-00
Part Marking
83503 83503 PE83503-EK
Description
PE83503-08MSOP-100A PE83503-08MSOP-2000C PE83503-08MSOP-EK
Package
8-lead MSOP 8-lead MSOP Evaluation Board
Shipping Method
50 pcs. / Tube 2000 pcs. / T&R 1 / Box
Document No. 70-0126-02 www.psemi.com
(c)2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 7 of 8
PE83503
Product Specification
Sales Offices
The Americas Peregrine Semiconductor Corporation
9450 Carroll Park Drive San Diego, CA 92121 Tel: 858-731-9400 Fax: 858-731-9499
North Asia Pacific Peregrine Semiconductor K.K.
Teikoku Hotel Tower 10B-6 1-1-1 Uchisaiwai-cho, Chiyoda-ku Tokyo 100-0011 Japan Tel: +81-3-3502-5211 Fax: +81-3-3502-5213
Europe Peregrine Semiconductor Europe
Batiment Maine 13-15 rue des Quatre Vents F-92380 Garches, France Tel: +33-1-4741-9173 Fax : +33-1-4741-9173
Peregrine Semiconductor, Korea
#B-2402, Kolon Tripolis, #210 Geumgok-dong, Bundang-gu, Seongnam-si Gyeonggi-do, 463-480 S. Korea Tel: +82-31-728-4300 Fax: +82-31-728-4305
South Asia Pacific Peregrine Semiconductor, China
Shanghai, 200040, P.R. China Tel: +86-21-5836-8276 Fax: +86-21-5836-7652
Space and Defense Products
Americas: Tel: 858-731-9453 Europe, Asia Pacific: 180 Rue Jean de Guiramand 13852 Aix-En-Provence Cedex 3, France Tel: +33-4-4239-3361 Fax: +33-4-4239-7227
For a list of representatives in your area, please refer to our Web site at: www.psemi.com
Data Sheet Identification
Advance Information
The product is in a formative or design stage. The data sheet contains design target specifications for product development. Specifications and features may change in any manner without notice. The information in this data sheet is believed to be reliable. However, Peregrine assumes no liability for the use of this information. Use shall be entirely at the user's own risk. No patent rights or licenses to any circuits described in this data sheet are implied or granted to any third party. Peregrine's products are not designed or intended for use in devices or systems intended for surgical implant, or in other applications intended to support or sustain life, or in any application in which the failure of the Peregrine product could create a situation in which personal injury or death might occur. Peregrine assumes no liability for damages, including consequential or incidental damages, arising out of the use of its products in such applications. The Peregrine name, logo, and UTSi are registered trademarks and UltraCMOS and HaRP are trademarks of Peregrine Semiconductor Corp.
Preliminary Specification
The data sheet contains preliminary data. Additional data may be added at a later date. Peregrine reserves the right to change specifications at any time without notice in order to supply the best possible product.
Product Specification
The data sheet contains final data. In the event Peregrine decides to change the specifications, Peregrine will notify customers of the intended changes by issuing a DCN (Document Change Notice).
(c)2003-2006 Peregrine Semiconductor Corp. All rights reserved. Page 8 of 8
Document No. 70-0126-02 UltraCMOSTM RFIC Solutions

▲Up To Search▲

Price & Availability of PE8350306

	To Download PE8350306 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .